In-Field Scan

30. In-Field Scan

30.1. Introduction

In Field Scan (IFS) is a hardware feature to run circuit level tests on a CPU core to detect problems that are not caught by parity or ECC checks. Future CPUs will support more than one type of test which will show up with a new platform-device instance-id.

30.2. IFS Image

Intel provides a firmware file containing the scan tests via github [1]. Similar to microcode there is a separate file for each family-model-stepping. IFS Images are not applicable for some test types. Wherever applicable the sysfs directory would provide a “current_batch” file (see below) for loading the image.

30.3. IFS Image Loading

The driver loads the tests into memory reserved BIOS local to each CPU socket in a two step process using writes to MSRs to first load the SHA hashes for the test. Then the tests themselves. Status MSRs provide feedback on the success/failure of these steps.

The test files are kept in a fixed location: /lib/firmware/intel/ifs_<n>/ For e.g if there are 3 test files, they would be named in the following fashion: ff-mm-ss-01.scan ff-mm-ss-02.scan ff-mm-ss-03.scan (where ff refers to family, mm indicates model and ss indicates stepping)

A different test file can be loaded by writing the numerical portion (e.g 1, 2 or 3 in the above scenario) into the curent_batch file. To load ff-mm-ss-02.scan, the following command can be used:

# echo 2 > /sys/devices/virtual/misc/intel_ifs_<n>/current_batch

The above file can also be read to know the currently loaded image.

30.4. Running tests

Tests are run by the driver synchronizing execution of all threads on a core and then writing to the ACTIVATE_SCAN MSR on all threads. Instruction execution continues when:

  1. All tests have completed.

  2. Execution was interrupted.

  3. A test detected a problem.

Note that ALL THREADS ON THE CORE ARE EFFECTIVELY OFFLINE FOR THE DURATION OF THE TEST. This can be up to 200 milliseconds. If the system is running latency sensitive applications that cannot tolerate an interruption of this magnitude, the system administrator must arrange to migrate those applications to other cores before running a core test. It may also be necessary to redirect interrupts to other CPUs.

In all cases reading the corresponding test’s STATUS MSR provides details on what happened. The driver makes the value of this MSR visible to applications via the “details” file (see below). Interrupted tests may be restarted.

The IFS driver provides sysfs interfaces via /sys/devices/virtual/misc/intel_ifs_<n>/ to control execution:

Test a specific core:

# echo <cpu#> > /sys/devices/virtual/misc/intel_ifs_<n>/run_test

when HT is enabled any of the sibling cpu# can be specified to test its corresponding physical core. Since the tests are per physical core, the result of testing any thread is same. All siblings must be online to run a core test. It is only necessary to test one thread.

For e.g. to test core corresponding to cpu5

# echo 5 > /sys/devices/virtual/misc/intel_ifs_<n>/run_test

Results of the last test is provided in /sys:

$ cat /sys/devices/virtual/misc/intel_ifs_<n>/status
pass

Status can be one of pass, fail, untested

Additional details of the last test is provided by the details file:

$ cat /sys/devices/virtual/misc/intel_ifs_<n>/details
0x8081

The details file reports the hex value of the test specific status MSR. Hardware defined error codes are documented in volume 4 of the Intel Software Developer’s Manual but the error_code field may contain one of the following driver defined software codes:

0xFD

Software timeout

0xFE

Partial completion

30.5. Driver design choices

1) The ACTIVATE_SCAN MSR allows for running any consecutive subrange of available tests. But the driver always tries to run all tests and only uses the subrange feature to restart an interrupted test.

2) Hardware allows for some number of cores to be tested in parallel. The driver does not make use of this, it only tests one core at a time.

struct ifs_data

attributes related to intel IFS driver

Definition:

struct ifs_data {
    int loaded_version;
    bool loaded;
    bool loading_error;
    int valid_chunks;
    int status;
    u64 scan_details;
    u32 cur_batch;
    u32 generation;
    u32 chunk_size;
    u32 array_gen;
};

Members

loaded_version

stores the currently loaded ifs image version.

loaded

If a valid test binary has been loaded into the memory

loading_error

Error occurred on another CPU while loading image

valid_chunks

number of chunks which could be validated.

status

it holds simple status pass/fail/untested

scan_details

opaque scan status code from h/w

cur_batch

number indicating the currently loaded test file

generation

IFS test generation enumerated by hardware

chunk_size

size of a test chunk

array_gen

test generation of array test